描述
LW-40/18 Nitrogen Compressor – High-Pressure Oil-Free N2 Booster for Demanding Industrial Applications
Engineered to deliver 40 m³/min at 1.80 MPa discharge pressure, the LW-40/18 is a two-stage, two-row oil-free piston nitrogen compressor purpose-built for high-pressure nitrogen injection, gas liquefaction pre-compression, and critical petrochemical process applications. Zero oil contamination, continuous-duty rated, and optimized for sustained operation at elevated pressure.
产品概述
这 LW-40/18 nitrogen compressor occupies a unique position at the intersection of substantial flow capacity and elevated discharge pressure within our oil-free piston compressor portfolio. With a rated capacity of 40 m³/min and an exceptional 1.80 MPa discharge pressure, this unit addresses the most demanding nitrogen compression requirements in industrial gas infrastructure where both high flow and high pressure are simultaneously required.
What distinguishes the LW-40/18 from conventional high-pressure alternatives is its completely oil-free compression mechanism. The piston rings and rider bands are fabricated from advanced self-lubricating PTFE composite materials that operate without any hydrocarbon lubricants. This intrinsic oil-free characteristic ensures the nitrogen product stream achieves ISO 8573-1 0级认证 natively, making the unit immediately suitable for food-grade nitrogen, pharmaceutical process gas, electronics-grade inerting, and petrochemical reactor blanketing without additional downstream purification equipment.
The compressor architecture follows a two-stage, two-row (二列二级) configuration that optimally manages the substantial pressure ratio required for 1.80 MPa discharge. By dividing the compression duty across two cylinders with an inter-stage cooler, the LW-40/18 maintains thermal stability and preserves the integrity of the PTFE sealing elements even under sustained maximum-load operation. The robust construction—2860 × 1685 × 2610 mm 和 7.00 tonnes—reflects the heavy-duty engineering required for high-pressure industrial service.
Technical Specifications – LW-40/18
| 范围 | 价值 | 单元 |
|---|---|---|
| 模型 | LW-40/18 | – |
| 图案 | Two-stage, Two-row (二列二级) | – |
| 容量 | 40 | 立方米/分钟 |
| 排气压力 | 1.80 | 兆帕 |
| 压缩机尺寸（长×宽×高） | 2860 × 1685 × 2610 | 毫米 |
| 重量 | 7.00 | t |
| 力量 | 400 | 千瓦 |
| 电压 | 6千或1万 | V |
| 气体介质 | 氮气（N₂） | – |
| 润滑 | 无油 | – |
* 所有规格均在标准参考条件下（ISO 1217，附录 C）测得。实际性能可能因现场海拔、环境温度和进气条件而异。
主要特性及工程优势
1. High-Pressure Oil-Free PTFE Sealing Technology
The LW-40/18 employs a specialized self-lubricating piston ring and rider band system manufactured from high-performance PTFE composites reinforced with glass fiber, bronze particulates, and molybdenum disulfide. This advanced material formulation achieves a coefficient of friction below 0.05 without any external hydrocarbon lubrication, completely eliminating oil vapor carryover risk. The rings are specifically engineered for the elevated discharge temperatures and pressures associated with 1.80 MPa operation, maintaining dimensional stability and sealing integrity up to 200°C. For operators in regulated industries, this delivers native ISO 8573-1 Class 0 compliance without downstream filtration capital or operating costs.
2. Two-Stage Compression for Extreme Pressure Ratios
这 two-stage compression architecture of the LW-40/18 is thermodynamically essential for managing the extreme pressure ratio required to achieve 1.80 MPa discharge from near-atmospheric suction. By dividing the compression duty between a low-pressure cylinder and a high-pressure cylinder, the compressor limits the discharge temperature of each stage to below 165°C. A high-efficiency shell-and-tube intercooler between stages removes the heat of compression, preventing thermal degradation of the PTFE sealing elements and extending valve plate service life by approximately 45% compared to single-stage designs attempting equivalent pressure ratios. This staged approach is fundamental to achieving reliable continuous operation at 1.80 MPa.
3. Reinforced Heavy-Duty Frame for High-Pressure Service
主框架由……铸造而成 GG30 灰铸铁 (equivalent to ASTM A48 Class 35B) with thicker wall sections and reinforced ribbing compared to lower-pressure models. The integral cooling water passages are precision-machined to ensure uniform thermal distribution across the cylinder block. The two-row opposed-cylinder arrangement provides natural first-order force cancellation, reducing unbalanced inertia forces transmitted to the foundation by over 80% versus single-row designs. Despite the 7.00-tonne weight, this mechanical balance permits installation on a reinforced concrete inertia block of 12–14 tonnes, significantly lighter than would be required for an equivalent single-row high-pressure compressor.
4. High-Power Medium-Voltage Motor Drive
The LW-40/18 is driven by a 400 kW medium-voltage induction motor available in either 6kV or 10kV configurations, conforming to IEC 60034-1 efficiency class IE3. The 400 kW power rating reflects the substantial energy input required for high-pressure compression at 40 m³/min capacity. Direct integration into industrial medium-voltage distribution networks eliminates the need for oversized low-voltage switchgear and heavy-gauge cabling. For facilities with existing 6kV or 10kV bus systems, the LW-40/18 offers seamless electrical compatibility, reducing infrastructure costs and improving overall energy efficiency through lower I²R losses.
应用场景
High-Pressure Nitrogen Injection for Enhanced Oil Recovery
In oilfield operations, the LW-40/18 serves as the primary high-pressure nitrogen injection compressor for enhanced oil recovery (EOR) and pressure maintenance programs. The 1.80 MPa discharge pressure is sufficient for direct injection into reservoir formations at depths up to 1,500 meters, where nitrogen displaces crude oil and maintains reservoir pressure. The 40 m³/min capacity supports multiple injection wells operating simultaneously. The oil-free design is critical in EOR applications because any hydrocarbon contamination from lubricated compressors would alter reservoir wettability and reduce oil displacement efficiency, directly impacting production yields.
Gas Liquefaction Pre-Compression
In small to medium-scale LNG and industrial gas liquefaction plants, the LW-40/18 nitrogen compressor provides the high-pressure nitrogen required for pre-cooling and liquefaction cycle support. The 1.80 MPa discharge pressure is adequate for nitrogen expander cycles and mixed-refrigerant pre-cooling systems. The oil-free compression path ensures that nitrogen used for process inerting and equipment purging does not introduce contaminants that could freeze out in cryogenic heat exchangers, causing blockages and operational disruptions.
Petrochemical Reactor Inerting & Catalyst Preservation
In petrochemical and refinery operations, the LW-40/8 provides high-pressure nitrogen for reactor inerting during startup and shutdown, catalyst bed preservation during extended outages, and emergency nitrogen injection into process vessels. The 1.80 MPa discharge pressure exceeds the operating pressure of most process reactors and vessels, allowing direct nitrogen injection without intermediate boosting. The continuous-duty rating ensures nitrogen availability during extended turnaround campaigns lasting several weeks. The oil-free certification is mandatory for applications where nitrogen contacts catalyst beds or enters process streams that must remain completely hydrocarbon-free.
High-Pressure Pipeline Testing & Commissioning
Natural gas and process pipeline construction projects require high-pressure nitrogen for hydrostatic testing, leak testing, drying, and commissioning before introducing hydrocarbon products. The LW-40/18’s 1.80 MPa discharge pressure is suitable for pressure testing pipelines rated up to Class 600 (ANSI B16.5). The 40 m³/min capacity enables rapid pressurization of long pipeline sections, reducing commissioning time and labor costs. The oil-free design prevents oil contamination of pipeline interiors that would require costly cleaning before product introduction.
材料与施工
The LW-40/18 is constructed from premium materials specifically selected for high-pressure nitrogen service, corrosion resistance, and extended operational life under demanding conditions:
| 成分 | 材料 | 规格 |
|---|---|---|
| Cylinder Block | 灰铸铁 | GG30 / HT300, reinforced wall sections, integral cooling jackets |
| 曲轴 | 锻造合金钢 | 42CrMo4, Q&T, ISO 1940 G2.5 dynamically balanced, nitrided journals |
| 活塞环 | 聚四氟乙烯-玻璃-青铜-二硫化钼复合材料 | Self-lubricating, high-temp rated to 200°C, wear rate <0.03 mm/1000h |
| 骑手带 | 聚四氟乙烯复合材料 | Piston guidance, anti-scuffing, high-load capacity |
| 阀板 | 不锈钢 | SS316, concentric ring spring-loaded, high-pressure rated |
| Connecting Rods | Forged Steel with Babbitt Bearings | Precision-machined, pressure-lubricated big end, high-load design |
| Intercooler | 碳钢外壳/316不锈钢管材 | ASME VIII Div.1, 1.5× hydrotest, 30 min hold |
| 后冷却器 | 碳钢外壳/316不锈钢管材 | High-pressure finned tube design, 32°C cooling water rated |
| 高压管道 | Seamless Carbon Steel | ASTM A106 Grade B, Schedule 80, 100% X-ray inspected |
所有承压部件的设计和制造均严格按照以下规定进行： ASME BPVC 第 VIII 节第 1 部分 or Chinese GB 150 standards. Every weld joint undergoes 100% radiographic inspection (RT) per ASME Section V, Article 2. Each completed pressure vessel is subjected to a hydrostatic pressure test at 1.5 times the maximum allowable working pressure (MAWP) for a minimum hold period of 30 minutes. High-pressure piping connections are 100% ultrasonic tested (UT) to detect any internal defects.
安装和维护指南
基础及结构要求
The LW-40/18 has a dry weight of 7.00 tonnes and a center of gravity approximately 950 mm above the baseplate. The two-row opposed-cylinder design minimizes unbalanced forces, permitting installation on a reinforced concrete inertia block of 12–14 tonnes. The block must be mounted on heavy-duty elastomeric vibration isolators (natural frequency 5–7 Hz) to prevent vibration transmission to adjacent structures and sensitive instrumentation. Minimum clearance requirements: 1.5 m on the non-drive side for valve access, 1.2 m on the drive side for motor maintenance, and 2.5 m overhead for crane access during major overhauls. The foundation must be designed to withstand the dynamic loads associated with 400 kW motor starting torque.
冷却水系统设计
冷却水需求量约为 48 m³/h at an inlet temperature not exceeding 32°C. The water distribution circuit supplies the cylinder jackets, intercooler, and aftercooler in parallel branches with individual flow control valves. Water quality specifications are stringent due to the high-pressure service: pH 6.5–8.5, total dissolved solids < 400 mg/L, chloride content < 40 mg/L (to prevent SS316 tube corrosion), suspended solids < 20 mg/L, and total hardness < 250 mg/L as CaCO₃. For sites with marginal water quality, a closed-loop cooling tower with side-stream filtration, water softening, and chemical treatment is mandatory to prevent scale formation and corrosion in the high-pressure coolers.
预防性维护计划
| 间隔 | 服务项目 | 需要采取的行动 |
|---|---|---|
| 日常的 | 运行检查 | Check vibration levels, abnormal noise, cooling water flow, discharge temperature, pressure relief valve integrity |
| 250小时 | Valve Plate Inspection | Remove and inspect suction/discharge valves for carbon deposits, spring fatigue, cracking, or seat erosion |
| 1000小时 | Piston Ring Wear Assessment | 测量活塞环槽间隙；如果间隙超过 0.20 毫米，则更换活塞环。 |
| 3000小时 | 中期大修 | Replace all piston rings, rider bands, and valve plate assemblies; inspect intercooler tubes |
| 6000小时 | 大修 | Inspect crankshaft journals, measure main and big-end bearing clearances, replace bearings if >0.06 mm |
The oil-free design of the LW-40/18 dramatically simplifies maintenance compared to lubricated alternatives. There are no oil changes, no oil analysis, no filter replacements, and no separator cartridge changes. The primary consumable wear items are the 聚四氟乙烯活塞环和活塞环带, which typically achieve 3,000–5,000 hours of service life under clean nitrogen conditions at high pressure. Valve plate assemblies generally require refurbishment at 2,000–3,500 hours due to the elevated operating pressures.
合规与安全认证
The LW-40/18 nitrogen compressor is designed, manufactured, and tested to meet or exceed the following international standards and regulatory frameworks:
ASME BPVC 第 VIII 部分第 1 部分、GB 150-2011、PED 2014/68/EU 模块 A
IEC 60034-1（IE3能效）、IEC 60204-1、ISO 12100机械安全
ISO 8573-1 0 级（含油量），经 TÜV 莱茵独立测试
ISO 9001:2015 (Quality Management), ISO 14001:2015 (Environmental Management)
Nitrogen is classified as a simple asphyxiant gas. At 1.80 MPa, nitrogen releases from the LW-40/18 pose additional hazards due to high-velocity gas jets and rapid expansion cooling. All installations must incorporate continuous oxygen deficiency monitoring in the compressor room and all adjacent areas. Ventilation systems must maintain ambient oxygen above 19.5% volume per OSHA 29 CFR 1910.146. Emergency shutdown interlocks should activate at 19.5% O₂ (alarm) and trigger automatic compressor isolation at 18.0% O₂ (hard shutdown). High-pressure relief systems must discharge to safe locations away from personnel areas. All high-pressure piping must be protected against mechanical damage and clearly marked with pressure ratings.
性能与效率分析
The LW-40/18 achieves a specific power consumption of approximately 10.00 kW per m³/min of nitrogen delivered at 1.80 MPa discharge pressure. This efficiency metric reflects the substantial thermodynamic work required for high-pressure compression and is competitive within the high-pressure oil-free piston compressor segment. For comparison, oil-lubricated screw compressors operating at equivalent pressure ratios typically consume 10.5–12.0 kW/m³/min, while multi-stage diaphragm compressors (often selected for high-pressure oil-free applications) can exceed 14 kW/m³/min.
Over a standard 8,000-hour annual operating schedule, the LW-40/18’s efficiency advantage generates approximately 160,000–400,000 kWh of annual energy savings compared to less efficient alternatives. At an average industrial electricity tariff of $0.08/kWh, this represents $12,800–$32,000 in direct operating cost reduction per year. However, the primary economic justification for the LW-40/18 is typically the elimination of oil-related consumables and the avoidance of downstream purification equipment that would be mandatory with lubricated alternatives.
这 total cost of ownership for high-pressure nitrogen compression is further reduced by the absence of oil in the compression path. A typical oil-lubricated compressor of this pressure rating would require high-pressure coalescing filters, activated carbon adsorbers, continuous oil monitoring, and periodic oil replacement that collectively add $15,000–$25,000 annually in operating costs. The LW-40/18’s oil-free design eliminates these expenses entirely while delivering superior product purity.
定制化和OEM能力
We offer comprehensive customization options to adapt the LW-40/18 to specific site conditions, integration requirements, and end-user specifications:
- Skid-Mounted Turnkey Packages: The compressor, motor, intercooler, aftercooler, high-pressure instrumentation, and control panel are pre-assembled on a reinforced structural steel skid with integrated lifting lugs and anchor bolt templates. Factory pre-testing of all systems reduces field commissioning time by approximately 60%.
- 危险区域配置： ATEX Zone 2 and IECEx compliant motor and electrical enclosures are available for oilfield and petrochemical installations. Integrated gas detection, automatic ventilation interlocks, and explosion-proof instrumentation can be incorporated into the control system.
- 高级过程控制： Optional Siemens S7-1200 or Allen-Bradley CompactLogix PLC with 10-inch HMI touchscreen, remote monitoring via Modbus TCP/IP or OPC-UA, and seamless DCS/SCADA integration. Automatic load/unload control, anti-surge protection, and emergency shutdown logic are standard.
- High-Pressure Package Options: Integrated high-pressure storage vessels, pressure regulation skids, and distribution manifolds can be supplied as part of a complete nitrogen injection package. All high-pressure components are designed and tested to the same standards as the compressor.
- OEM & Private Label: Custom paint colors, branded nameplates, and localized documentation packages are available for gas equipment distributors and system integrators serving oilfield and industrial markets.
可提供自定义配置 最小起订量 1 件. Engineering review and proposal generation typically require 7–10 business days due to the complexity of high-pressure applications. Standard delivery time is 14–16 weeks; repeat orders are delivered in 10–12 weeks from order confirmation.
Case Study: Oilfield Nitrogen Injection for Enhanced Recovery
客户： An independent oil producer operating mature oilfields in the Middle East
挑战： The client’s oilfields had entered decline phase with reservoir pressure dropping below the bubble point, causing gas breakout and reduced oil mobility. Conventional waterflooding was ineffective due to reservoir heterogeneity. The client required high-pressure nitrogen injection to maintain reservoir pressure and improve sweep efficiency, but existing oil-lubricated compressors were contaminating the injection gas with hydrocarbons, altering reservoir wettability and reducing displacement efficiency.
解决方案： We supplied an LW-40/18 oil-free nitrogen compressor configured on a custom skid with integrated high-pressure aftercooler, moisture separator, and a Siemens S7-1200 PLC control panel with remote monitoring. The 1.80 MPa discharge pressure enabled direct injection into reservoir formations at 1,200–1,400 meters depth. A 10 m³ high-pressure surge vessel was installed downstream to buffer injection rate fluctuations. The skid was designed for desert operation with sand filtration, high-ambient-temperature cooling, and C5-M corrosion protection.
Quantified Results After 36 Months:
- Reservoir pressure: Maintained at 85% of original versus 62% with waterflooding alone
- Oil production rate: Increased by 18% compared to pre-nitrogen injection baseline
- 氮油含量： <0.01 mg/m³, eliminating reservoir wettability alteration
- Compressor availability: 97.5% over 36 months, with only scheduled maintenance shutdowns
- Operating cost: 32% lower than the previous oil-lubricated compressor system due to elimination of oil-related maintenance
“The LW-40/18 has been the cornerstone of our nitrogen EOR program. The oil-free design gives us confidence that we’re not compromising reservoir performance, and the reliability has exceeded our expectations in a harsh desert environment.” — Reservoir Engineering Manager
常见问题解答及选购指南
相关产品及解决方案
ZW Series Multi-Stage High-Pressure Compressors
Vertical, multi-stage oil-free compressors for oxygen, nitrogen, hydrogen, and specialty gases. Discharge pressures up to 9.00 MPa for ultra-high-pressure gas filling, cylinder charging, and specialized chemical process applications.
DW Series Medium-Pressure Nitrogen Compressors
Medium to high-pressure oil-free compressors (0.40–2.00 MPa) for nitrogen injection, pipeline boosting, and chemical synthesis. Capacities from 2 to 130 m³/min with two-stage and multi-stage configurations.
MW Series Medium-Pressure Compressors
Medium-pressure oil-free compressors (1.0–4.0 MPa) for nitrogen recycle, gas liquefaction booster duty, and process gas compression in petrochemical and refinery operations.
如需全面了解我们的 工业氮气压缩机 产品组合包括无油氧气压缩机、氢气压缩机、二氧化碳压缩机和定制工程特种气体解决方案，请联系我们的应用工程团队或浏览我们的在线产品目录。
Ready to Deploy High-Pressure Nitrogen Compression?
Our application engineers are standing by to evaluate your high-pressure nitrogen requirements, suction conditions, discharge pressure targets, and integration constraints. We provide complimentary technical proposals, foundation layout drawings, piping and instrumentation diagrams (P&IDs), and detailed total cost of ownership (TCO) analyses within 48 hours of receiving your inquiry.
电子邮件： [email protected] | 24小时内回复
