LW-25/16 Nitrogen Compressor – High-Pressure Oil-Free N2 Booster for 1.60 MPa Industrial Applications

Engineered to deliver 25 m³/min at 1.60 MPa discharge pressure, the LW-25/16 is a two-stage, two-row oil-free piston nitrogen compressor designed for high-pressure nitrogen injection, pipeline boosting, and demanding petrochemical process applications. Zero lubricant contamination, continuous-duty rated, and built for 24/7 operation at elevated pressure.

نظرة عامة على المنتج

ال LW-25/16 nitrogen compressor occupies a specialized position within our oil-free piston compressor portfolio, bridging the gap between medium-pressure nitrogen distribution and high-pressure process applications. With a rated capacity of 25 m³/min واستثنائي ضغط التفريغ 1.60 ميجا باسكال, this unit addresses the most demanding nitrogen compression requirements in industrial gas infrastructure where both substantial flow and elevated pressure are simultaneously required.

What distinguishes the LW-25/16 from conventional high-pressure alternatives is its آلية ضغط خالية تمامًا من الزيت. The piston rings and rider bands are fabricated from advanced self-lubricating PTFE composite materials specifically formulated for high-pressure service. These components operate without any hydrocarbon lubricants, ensuring the nitrogen stream remains completely free of oil contamination even at the elevated temperatures and pressures associated with 1.60 MPa discharge. This intrinsic oil-free characteristic delivers شهادة ISO 8573-1 من الفئة 0 natively, eliminating the need for costly downstream oil-removal systems that would otherwise be mandatory in high-pressure applications.

يستخدم الضاغط two-stage, two-row (二列二级) configuration that is essential for managing the extreme pressure ratio required to achieve 1.60 MPa discharge from near-atmospheric inlet conditions. The staged compression distributes thermal load across two cylinders, with an independent high-efficiency intercooler between stages maintaining gas temperatures within safe operating limits. The robust cast-iron frame and precision-forged crankshaft are engineered to withstand the substantial mechanical forces generated by high-pressure operation, with a rated service life exceeding 100,000 hours في إطار بروتوكولات الصيانة القياسية.

Technical Specifications – LW-25/16

* جميع المواصفات مصنفة وفقًا لظروف مرجعية قياسية (ISO 1217، الملحق ج). قد يختلف الأداء الفعلي بناءً على ارتفاع الموقع ودرجة الحرارة المحيطة وظروف المدخل.

الميزات الرئيسية والمزايا الهندسية

1. تقنية منع التسرب عالية الضغط الخالية من الزيت باستخدام مادة PTFE

The LW-25/16 utilizes a proprietary high-pressure self-lubricating piston ring and rider band system manufactured from advanced PTFE composites reinforced with high-strength glass fiber and bronze particulates. This material formulation is specifically engineered for the extreme pressure differentials and elevated temperatures encountered at 1.60 MPa discharge pressure. The rings achieve a coefficient of friction below 0.06 without any external hydrocarbon lubrication, completely eliminating oil contamination risk. For high-pressure nitrogen users in petrochemical, pharmaceutical, and specialty gas applications, this delivers native ISO 8573-1 Class 0 compliance without the complexity, cost, and reliability concerns of downstream oil-filtration systems operating at elevated pressure.

2. Two-Stage Compression for Extreme Pressure Ratios

ال two-stage compression architecture is absolutely critical for achieving 1.60 MPa discharge from atmospheric inlet conditions, representing an overall pressure ratio of approximately 16:1. By dividing this extreme ratio between a low-pressure cylinder and a high-pressure cylinder, the LW-25/16 limits the discharge temperature of each stage to below 160°C, preserving the structural integrity of the PTFE sealing elements. A high-efficiency shell-and-tube intercooler between stages removes the substantial heat of compression, with cooling water flow designed to maintain inter-stage temperatures below 45°C even at maximum continuous load. This thermal management extends valve plate life by approximately 50% compared to single-stage designs attempting equivalent pressure ratios.

3. Reinforced Heavy-Duty Frame for High-Pressure Operation

الهيكل الرئيسي مصبوب من GG30 gray cast iron (upgraded from the GG25 used in lower-pressure models) with thicker wall sections and reinforced bearing pedestals to withstand the substantially higher mechanical loads generated by 1.60 MPa discharge pressure. The two-row opposed-cylinder arrangement provides natural first-order force cancellation, reducing unbalanced inertia forces transmitted to the foundation by over 80% compared to single-row designs. This mechanical advantage is particularly important for high-pressure compressors where the peak cylinder forces are significantly elevated. The forged steel crankshaft is dynamically balanced to ISO 1940 G2.5 standards and features enlarged bearing journals to accommodate the higher bearing loads.

4. Flexible Voltage Configuration for Industrial Integration

The LW-25/16 is available with a 200 kW drive motor in three voltage configurations: 380V for facilities with low-voltage distribution infrastructure, or 6kV/10kV for direct integration into medium-voltage industrial networks. The 380V option is ideal for smaller installations or retrofit projects where medium-voltage infrastructure is not available. The 6kV and 10kV options eliminate the need for step-down transformers in large industrial facilities, reducing electrical infrastructure costs and improving overall energy efficiency. All motor configurations conform to IEC 60034-1 efficiency class IE3.

سيناريوهات التطبيق

High-Pressure Nitrogen Pipeline Boosting

In industrial gas distribution networks spanning multiple facilities or large plant sites, the LW-25/16 serves as a high-pressure nitrogen booster station to overcome pipeline friction losses and maintain adequate pressure at remote consumption points. Its 1.60 MPa discharge pressure provides sufficient head for distribution over distances exceeding 5 km, making it ideal for centralized nitrogen supply to multiple process units, storage tank farms, and remote loading stations. The 25 m³/min capacity supports medium-scale industrial complexes with multiple simultaneous nitrogen consumers. The oil-free design is critical in pipeline applications because any oil contamination would propagate throughout the entire distribution network, potentially affecting all downstream consumers.

Petrochemical Reactor Inerting & Catalyst Preservation

Petrochemical reactors, catalytic crackers, and hydroprocessing units require high-pressure nitrogen for reactor inerting during startup and shutdown, catalyst bed preservation during standby periods, and emergency depressurization. The LW-25/16 high-pressure nitrogen compressor delivers the 1.60 MPa pressure required to overcome reactor system pressures and inject nitrogen directly into process vessels. The oil-free design is absolutely mandatory in these applications because oil contamination would poison expensive catalyst beds, permanently degrading catalytic activity and requiring costly catalyst replacement or regeneration.

Nitrogen Gas Filling & Cylinder Charging Stations

Industrial gas filling stations and cylinder charging facilities require high-pressure nitrogen compressors to fill standard gas cylinders (typically 15 MPa working pressure) and tube trailers (up to 20 MPa). While the LW-25/16’s 1.60 MPa discharge pressure does not directly achieve cylinder filling pressure, it serves as an intermediate booster in multi-stage compression trains, compressing nitrogen from atmospheric or low-pressure sources to the suction pressure of high-pressure diaphragm or piston compressors. The oil-free design ensures that nitrogen entering the high-pressure stage is completely uncontaminated, preventing oil accumulation in high-pressure cylinders and tube trailers that could compromise gas purity and create safety hazards.

Food & Beverage High-Pressure Nitrogen Injection

Large-scale food and beverage processing facilities utilize high-pressure nitrogen for product dispensing systems, pressurized packaging, and controlled atmosphere storage at elevated pressure. The LW-25/16’s 1.60 MPa discharge pressure is sufficient for direct injection into pressurized product tanks and dispensing systems without intermediate boosting. The oil-free certification ensures compliance with FDA 21 CFR 173.310 and EU Regulation 231/2012 for food-contact nitrogen. The 25 m³/min capacity supports high-throughput production lines where multiple dispensing stations operate simultaneously.

المواد والإنشاءات

The LW-25/16 is constructed from premium materials specifically selected for high-pressure nitrogen service, thermal stress resistance, and extended operational life:

تم تصميم وتصنيع جميع المكونات التي تتحمل الضغط وفقًا لمعايير صارمة. ASME BPVC القسم الثامن القسم 1 or Chinese GB 150 standards, with additional safety margins for high-pressure service. Every weld joint undergoes 100% radiographic inspection (RT) per ASME Section V, Article 2, and each completed pressure vessel is subjected to a hydrostatic pressure test at 1.5 times the maximum allowable working pressure (MAWP) for a minimum hold period of 30 minutes. High-pressure piping is 100% pneumatically tested at 1.1× MAWP after hydrostatic testing.

إرشادات التركيب والصيانة

متطلبات الأساس والهيكل

The LW-25/16 has a dry weight of 4.50 tonnes and a center of gravity approximately 950 mm above the baseplate. Due to the substantially higher mechanical forces generated by 1.60 MPa discharge pressure, a reinforced concrete inertia block of 9–12 tonnes is required. The block must be mounted on heavy-duty vibration isolators (natural frequency 5–7 Hz) capable of accommodating the elevated dynamic loads. Foundation design must account for the peak cylinder forces, which are significantly higher than those of lower-pressure compressors of equivalent capacity. Minimum clearance requirements: 1.5 m on the non-drive side for valve access, 1.2 m on the drive side for motor maintenance, and 2.0 m overhead for crane access during major overhauls.

تصميم نظام مياه التبريد

يبلغ الطلب على مياه التبريد ما يقارب 28 m³/h at an inlet temperature not exceeding 32°C. The high-pressure intercooler and aftercooler require particularly effective cooling to manage the substantial heat of compression at 1.60 MPa. Water quality specifications: pH 6.5–8.5, total dissolved solids < 400 mg/L, chloride content < 40 mg/L (critical for SS316 tube corrosion prevention), suspended solids < 25 mg/L, and total hardness < 250 mg/L as CaCO₃. A closed-loop cooling tower with side-stream filtration and chemical treatment is strongly recommended for all installations to ensure consistent water quality and prevent scale formation in high-pressure heat exchanger tubes.

جدول الصيانة الوقائية

The oil-free design of the LW-25/16 significantly reduces maintenance complexity compared to lubricated high-pressure alternatives. There are no oil changes to schedule, no lubricating oil samples to analyze, no oil filter elements to replace, and no high-pressure oil separator cartridges to monitor. The primary consumable wear items are the حلقات مكابس PTFE وأحزمة تثبيت, which typically achieve 3,500–5,000 hours of service life under clean nitrogen conditions at high pressure. Valve plate assemblies generally achieve 2,000–3,500 hours before requiring refurbishment in high-pressure service.

شهادات الامتثال والسلامة

The LW-25/16 nitrogen compressor is designed, manufactured, and tested to meet or exceed the following international standards and regulatory frameworks:

تحليل الأداء والكفاءة

The LW-25/16 achieves a specific power consumption of approximately 8.00 kW per m³/min of nitrogen delivered at 1.60 MPa discharge pressure. This efficiency metric reflects the thermodynamic challenges inherent in compressing to elevated pressure ratios, yet remains competitive within the high-pressure oil-free piston compressor segment. For comparison, oil-lubricated screw compressors operating at equivalent pressure ratios typically consume 8.5–9.5 kW/m³/min, while high-pressure diaphragm compressors (often selected for oil-free applications) can exceed 12 kW/m³/min.

Over a standard 8,000-hour annual operating schedule, the LW-25/16’s efficiency advantage versus less efficient alternatives yields approximately 100,000–240,000 kWh of annual energy savings. At an average industrial electricity tariff of $0.08/kWh, this represents $8,000–$19,200 in direct operating cost reduction per year. However, the primary economic driver for LW-25/16 selection is typically the التخلص من المواد الاستهلاكية المتعلقة بالنفط ومعدات التنقية اللاحقة rather than marginal energy savings.

ال التكلفة الإجمالية لامتلاك نظام ضغط النيتروجين عالي الضغط is further reduced by the absence of oil in the compression path. A typical oil-lubricated high-pressure compressor of this size requires coalescing filters, activated carbon adsorbers, oil monitoring instrumentation, and periodic oil changes that collectively add $15,000–$25,000 in annual operating costs. The LW-25/16’s oil-free design eliminates these expenses entirely while simultaneously improving reliability by removing the most common failure mode in high-pressure compressors: oil system contamination and degradation.

إمكانيات التخصيص وتصنيع المعدات الأصلية

We offer comprehensive customization options to adapt the LW-25/16 to specific site conditions, integration requirements, and end-user specifications:

• حزم جاهزة للتسليم مثبتة على قاعدة انزلاقية: The compressor, motor, intercooler, aftercooler, high-pressure instrumentation, and control panel are pre-assembled on a structural steel skid with integrated lifting lugs and anchor bolt templates. Factory pre-testing of all systems reduces field commissioning time by approximately 60% and minimizes startup risks.
• تكوينات المناطق الخطرة: ATEX Zone 2 and IECEx compliant motor and electrical enclosures are available for installations in petrochemical facilities where explosive atmospheres may occasionally be present. Integrated gas detection and automatic ventilation interlocks can be incorporated into the control system.
• التحكم المتقدم في العمليات: Optional Siemens S7-1200 or Allen-Bradley CompactLogix PLC with 10-inch HMI touchscreen, remote monitoring via Modbus TCP/IP or OPC-UA, and seamless integration with plant DCS/SCADA systems. Automatic load/unload control and variable frequency drive (VFD) compatibility optimize part-load efficiency.
• High-Pressure Safety Systems: Automatic pressure relief valves, rupture disc assemblies, high-pressure isolation valves, and emergency depressurization systems can be integrated into the discharge piping. All safety systems are designed to ASME BPVC Section VIII requirements.
• حماية البيئة: C5-M marine-grade coating systems for coastal installations; tropicalized electrical components for ambient temperatures up to 55°C; and IP54-rated acoustic enclosures reducing noise emission from 87 dB(A) to 74 dB(A) at 1 meter.
• تصنيع المعدات الأصلية والعلامات التجارية الخاصة: Custom paint colors, branded nameplates, and localized documentation packages for gas equipment distributors and system integrators.

تتوفر التكوينات المخصصة من الحد الأدنى للطلب: وحدة واحدة. Engineering review and proposal generation typically require 5–7 business days. Standard delivery time is 12–14 weeks; repeat orders are delivered in 8–10 weeks from order confirmation.

Case Study: Petrochemical Reactor Inerting System Upgrade

عميل: A major petrochemical complex in the Middle East operating polyethylene and polypropylene production units

تحدي: The client’s existing high-pressure nitrogen supply for reactor inerting and catalyst preservation was provided by two oil-lubricated reciprocating compressors (American brand, 20 years in service). Oil carryover into the nitrogen stream was contaminating Ziegler-Natta catalyst beds, reducing polymerization efficiency by 8–12% and requiring catalyst replacement every 14 months instead of the designed 24-month interval. The oil was also fouling reactor internals, necessitating unplanned shutdowns for cleaning. Annual losses from catalyst degradation and unplanned downtime exceeded $2.3 million.

حل: We supplied an LW-25/16 oil-free nitrogen compressor as the primary high-pressure nitrogen source, configured on a custom skid with integrated intercooler, aftercooler, high-pressure safety systems (relief valves, rupture discs, isolation valves), and a Siemens S7-1200 PLC control panel with SCADA integration. The 1.60 MPa discharge pressure met all reactor inerting and catalyst preservation requirements. A redundant standby unit was installed for 100% availability.

Quantified Results After 30 Months:

• Nitrogen oil content: Reduced from 5.8 mg/m³ to <0.01 mg/m³, achieving ISO 8573-1 Class 0 certification
• Catalyst replacement interval: Extended from 14 months to 28 months, saving $1.8 million/year in catalyst costs
• Polymerization efficiency: Improved by 9.5%, increasing annual production by 12,000 tonnes
• توقف غير مخطط له: مستبعد—zero oil-related shutdowns in 30 months
• Overall maintenance cost: Reduced by 38% through elimination of oil system repairs and catalyst-related cleaning

“The LW-25/16 has been transformative for our operations. The elimination of oil contamination has restored our catalyst performance to design levels and completely eliminated the unplanned shutdowns that were costing us millions. The payback period was under 12 months.” — Vice President of Operations, Petrochemical Complex

الأسئلة الشائعة ودليل الاختيار

المنتجات والحلول ذات الصلة

للحصول على نظرة عامة شاملة عن ضاغط نيتروجين صناعي للاطلاع على محفظتنا، بما في ذلك ضواغط الأكسجين الخالية من الزيت، وضواغط الهيدروجين، وضواغط ثاني أكسيد الكربون، وحلول الغازات المتخصصة المصممة حسب الطلب، يرجى الاتصال بفريق هندسة التطبيقات لدينا أو تصفح كتالوج منتجاتنا عبر الإنترنت.

هل أنت مستعد لترقية نظام النيتروجين عالي الضغط الخاص بك؟

Our application engineers are standing by to evaluate your high-pressure nitrogen flow requirements, suction conditions, discharge pressure targets, and integration constraints. We provide complimentary technical proposals, foundation layout drawings, piping and instrumentation diagrams (P&IDs), high-pressure safety system designs, and detailed total cost of ownership (TCO) analyses within 48 hours of receiving your inquiry.

بريد إلكتروني: [email protected] الرد خلال 24 ساعة