LW-13/30 نائٹروجن کمپریسر - 3.00 MPa ہائی پریشر پروسیس ایپلی کیشنز کے لیے درمیانی صلاحیت کا تیل سے پاک N2 بوسٹر

3.00 MPa ڈسچارج پریشر پر 13 m³/منٹ ڈیلیور کرنے کے لیے انجینئرڈ، LW-13/30 ایک دو مرحلوں والا، تین قطاروں والا آئل فری پسٹن نائٹروجن کمپریسر ہے جو ہائی پریشر نائٹروجن انجیکشن، گیس لیکیفیکشن بوسٹر ڈیوٹی، اور پیٹروکیمیکل پروسیس ایپلی کیشنز کا مطالبہ کرنے کے لیے ڈیزائن کیا گیا ہے۔ زیرو تیل کی آلودگی، مسلسل ڈیوٹی کی درجہ بندی، اور بلند دباؤ پر 24/7 صنعتی اعتبار کے لیے بنایا گیا ہے۔

پروڈکٹ کا جائزہ

دی LW-13/30 nitrogen compressor occupies a critical position within our oil-free piston compressor portfolio, bridging the gap between medium-capacity boosters and high-pressure process compressors. With a rated capacity of 13 m³/min اور ایک غیر معمولی 3.00 ایم پی اے ڈسچارج پریشر, this unit is purpose-built for applications where both substantial flow and elevated pressure are non-negotiable requirements.

What distinguishes the LW-13/30 from conventional alternatives is its مکمل طور پر تیل سے پاک کمپریشن کا راستہ. The piston rings and rider bands are precision-machined from advanced self-lubricating PTFE composite materials that operate without any hydrocarbon lubricants, ensuring the nitrogen stream remains completely uncontaminated. This intrinsic oil-free characteristic achieves ISO 8573-1 کلاس 0 سرٹیفیکیشن natively, eliminating the capital expenditure and ongoing maintenance burden of downstream oil-removal filtration systems that would be mandatory with lubricated alternatives.

The compressor architecture employs a two-stage, three-row (二列三级) configuration—a unique arrangement that divides the total pressure ratio across three compression cylinders arranged in two rows. This staged approach is essential for managing the extreme thermal loads associated with 3.00 MPa discharge pressure while preserving the integrity of the PTFE sealing elements. Each stage features an independent intercooler, ensuring gas temperatures remain within safe operating envelopes even during sustained maximum-capacity operation. The robust cast-iron frame and dynamically balanced forged steel crankshaft are rated for a minimum service life of 120,000 hours under standard maintenance protocols.

Technical Specifications – LW-13/30

* تمام وضاحتیں معیاری حوالہ جات کی شرائط پر درجہ بندی کی جاتی ہیں (ISO 1217، Annex C)۔ اصل کارکردگی سائٹ کی اونچائی، محیط درجہ حرارت، اور داخلی حالات کی بنیاد پر مختلف ہو سکتی ہے۔

کلیدی خصوصیات اور انجینئرنگ کے فوائد

1. Three-Stage Compression for Extreme Pressure Ratios

The LW-13/30 employs a unique two-stage, three-row (二列三级) architecture that divides the extreme pressure ratio required for 3.00 MPa discharge across three compression cylinders. This multi-stage approach is thermodynamically essential because a single-stage or even two-stage compressor would generate discharge temperatures exceeding the safe operating limit of PTFE sealing materials (approximately 180°C). By splitting the compression work across three stages with two inter-stage coolers, the LW-13/30 maintains per-stage discharge temperatures below 155°C, preserving PTFE ring integrity and extending valve plate life by approximately 50% compared to two-stage designs attempting equivalent pressure ratios. The three-row arrangement also provides improved force balance compared to single-row configurations, reducing foundation requirements.

2. High-Pressure Oil-Free PTFE Composite Sealing

The LW-13/30 utilizes a proprietary خود چکنا کرنے والی پسٹن کی انگوٹھی اور رائیڈر بینڈ اسمبلی manufactured from high-density PTFE composites specifically formulated for high-pressure, high-temperature service. These rings are reinforced with glass fiber and bronze particulates to achieve a coefficient of friction below 0.05 without any external hydrocarbon lubrication. At 3.00 MPa discharge pressure, the partial pressure of oil vapor would be extremely high in a lubricated compressor, making downstream oil removal virtually impossible. The oil-free design achieves native ISO 8573-1 Class 0 compliance, eliminating the need for coalescing filters, activated carbon adsorbers, and oil monitoring instrumentation that would add significant capital and operating costs to a lubricated system.

3. Reinforced Frame for High-Pressure Mechanical Loads

مرکزی فریم سے کاسٹ کیا گیا ہے۔ GG25 گرے کاسٹ آئرن with significantly reinforced wall sections, additional ribbing, and integral cooling water passages. The high-pressure cylinders feature thicker walls and enhanced structural support to withstand the peak gas forces associated with 3.00 MPa operation. The three-row arrangement distributes the mechanical loads across multiple crankshaft throws, reducing the peak bearing loads per cylinder and improving overall crankshaft longevity. The frame is dynamically analyzed using finite element modeling to ensure stress concentrations remain within safe limits under all operating conditions, including emergency shutdown transients.

4. Standard 380V Drive with High-Torque Motor

The LW-13/30 is driven by a 160 kW, 380V, 50Hz three-phase induction motor rated to IEC 60034-1 efficiency class IE3. The motor is specifically selected for high starting torque to overcome the substantial initial resistance of the three-row compression train. The standard 380V configuration integrates directly into existing low-voltage industrial distribution panels without requiring medium-voltage infrastructure, making this high-pressure compressor accessible to a wide range of industrial facilities. For sites with 6kV or 10kV bus systems, an optional motor with integrated step-down transformer can be supplied.

درخواست کے منظرنامے۔

High-Pressure Nitrogen Injection for Enhanced Oil Recovery

In oil and gas production, the LW-13/30 serves as a high-pressure nitrogen injection compressor for enhanced oil recovery (EOR) and miscible gas flooding operations. The 3.00 MPa discharge pressure is sufficient for injecting nitrogen into reservoirs at depths up to 2,000 meters, where the formation pressure requires high injection pressures to achieve effective displacement. The 13 m³/min capacity can serve multiple injection wells simultaneously through a centralized high-pressure distribution manifold. The oil-free design is critical in EOR applications because any oil contamination in the injected nitrogen would damage the reservoir formation, reduce permeability, and compromise oil recovery efficiency.

Gas Liquefaction & Cryogenic Process Booster

In nitrogen liquefaction plants and cryogenic process facilities, the LW-13/30 nitrogen booster compresses nitrogen from the liquefier cold end or storage vaporizer to the pressure required for distribution or further processing. The 3.00 MPa discharge pressure is adequate for feeding high-pressure nitrogen into cryogenic storage systems, driving nitrogen through multi-pass heat exchangers, and supplying high-pressure nitrogen for supercritical fluid extraction processes. The oil-free design prevents contamination of the cryogenic equipment, where even trace oil would freeze and block heat exchanger passages, causing costly shutdowns and equipment damage.

Petrochemical High-Pressure Reactor Inerting

In petrochemical and chemical synthesis operations, the LW-13/30 provides high-pressure nitrogen for reactor inerting, catalyst bed preservation, and emergency depressurization. The 3.00 MPa discharge pressure is sufficient to maintain positive inert gas blankets in high-pressure reactors operating at 2.00–2.50 MPa, preventing explosive vapor formation and protecting catalyst beds from oxidation during startup and shutdown. The 13 m³/min capacity can serve multiple reactors or process units through a centralized high-pressure nitrogen header. The oil-free certification is mandatory because any oil contamination would poison catalysts, degrade product quality, and create safety hazards in oxygen-sensitive processes.

High-Pressure Pipeline Testing & Commissioning

Natural gas pipelines, petrochemical process piping, and high-pressure vessel systems require nitrogen for hydrostatic testing, pneumatic testing, and commissioning purge operations. The LW-13/30’s 3.00 MPa discharge pressure is suitable for pressure testing systems rated up to 2.50 MPa design pressure (with appropriate safety margins per ASME B31.3). The 13 m³/min capacity allows rapid pressurization of large-diameter pipelines and vessels, reducing commissioning time. The oil-free design ensures that test nitrogen does not introduce contaminants that would require post-test cleaning or compromise the integrity of sensitive process systems.

مواد اور تعمیر

The LW-13/30 is constructed from premium materials selected for extreme high-pressure nitrogen compatibility, thermal resistance, and extended operational life:

تمام دباؤ برداشت کرنے والے اجزاء کو سختی کے مطابق ڈیزائن اور من گھڑت بنایا گیا ہے۔ ASME BPVC سیکشن VIII ڈویژن 1 یا چینی GB 150 معیارات۔ ہر ویلڈ جوائنٹ 100% ریڈیوگرافک معائنہ (RT) فی ASME سیکشن V، آرٹیکل 2 سے گزرتا ہے، اور ہر مکمل پریشر برتن کو 30 منٹ کی کم سے کم ہولڈ مدت کے لیے زیادہ سے زیادہ قابل اجازت ورکنگ پریشر (MAWP) سے 1.5 گنا زیادہ ہائیڈرو سٹیٹک پریشر ٹیسٹ کا نشانہ بنایا جاتا ہے۔ ہائی پریشر پائپنگ سسٹم سیملیس SS316 سے ANSI کلاس 900 فلینجڈ کنکشن کے ساتھ گھڑے گئے ہیں تاکہ 3.00 MPa آپریٹنگ پریشر پر لیک ٹائٹ سالمیت کو یقینی بنایا جا سکے۔

تنصیب اور دیکھ بھال کے رہنما خطوط

بنیاد اور ساختی تقاضے

The LW-13/30 has a dry weight of 6.60 tonnes and a center of gravity approximately 850 mm above the baseplate. Despite the three-row design, the opposed-cylinder arrangement provides reasonable force balance, permitting installation on a reinforced concrete inertia block of 10–12 tonnes. The block should be mounted on elastomeric vibration isolators (natural frequency 6–8 Hz). Minimum clearance requirements: 1.5 m on the non-drive side for valve access, 1.2 m on the drive side for motor maintenance, and 2.0 m overhead for crane access. The high-pressure discharge piping must be properly supported with spring hangers or flexible supports to prevent thermal expansion stress and vibration-induced fatigue at 3.00 MPa.

کولنگ واٹر سسٹم ڈیزائن

ٹھنڈے پانی کی طلب تقریباً ہے۔ 25 m³/h at an inlet temperature not exceeding 32°C. The water distribution circuit supplies the cylinder jackets and two intercoolers in parallel. Given the extreme pressure ratio, both intercoolers are critical for thermal management and must receive priority cooling water flow. Water quality specifications: pH 6.5–8.5, total dissolved solids < 500 mg/L, chloride content < 50 mg/L (to prevent SS316 tube corrosion), suspended solids < 30 mg/L, and total hardness < 300 mg/L as CaCO₃. A closed-loop cooling tower with side-stream filtration and chemical treatment is strongly recommended for all installations.

روک تھام کی بحالی کا شیڈول

The oil-free design of the LW-13/30 dramatically reduces maintenance complexity compared to lubricated alternatives. There are no oil changes, no oil analysis, no filter replacements, and no separator cartridge changes. The primary consumable wear items are the PTFE پسٹن کے حلقے اور سوار بینڈ, which typically achieve 3,000–5,000 hours of service life under clean nitrogen conditions at high pressure. The three-stage design distributes wear more evenly than two-stage configurations, reducing the frequency of major overhauls.

تعمیل اور حفاظتی سرٹیفیکیشن

The LW-13/30 nitrogen compressor is designed, manufactured, and tested to meet or exceed the following international standards and regulatory frameworks:

کارکردگی اور کارکردگی کا تجزیہ

The LW-13/30 achieves a specific power consumption of approximately 12.31 kW per m³/min of nitrogen delivered at 3.00 MPa discharge pressure. This specific power figure reflects the thermodynamic reality of ultra-high-pressure compression, where the work required increases substantially with pressure ratio. Within the high-pressure oil-free piston compressor segment (discharge pressure >2.50 MPa), this efficiency is highly competitive and significantly superior to diaphragm compressors, which are the primary alternative for oil-free high-pressure service. For comparison, oil-lubricated reciprocating compressors in similar ultra-high-pressure applications typically consume 13.0–15.0 kW/m³/min, while diaphragm compressors may exceed 18 kW/m³/min.

Over an 8,000-hour annual operating cycle, the LW-13/30’s efficiency advantage versus less efficient alternatives yields approximately 52,000–104,000 kWh of annual energy savings. At $0.08/kWh, this represents $4,160–$8,320 in direct electricity cost reduction per year. However, the primary economic justification for the LW-13/30 is typically the تیل سے متعلقہ استعمال کی اشیاء کا خاتمہ اور نیچے کی طرف سے تیل ہٹانے والے آلات سے اجتناب that would be mandatory with lubricated alternatives. The الٹرا ہائی پریشر نائٹروجن کمپریشن کے لیے ملکیت کی کل لاگت is reduced by an estimated 25–35% over a 10-year operational life when oil-free operation is compared to lubricated systems with full downstream purification.

The absence of oil in the compression path is particularly valuable at 3.00 MPa because oil contamination becomes exponentially more concentrated and more difficult to remove as pressure increases. At this pressure level, even advanced coalescing filters and activated carbon systems struggle to achieve sub-ppm oil content, and the energy penalty of operating such systems becomes substantial. The LW-13/30’s native oil-free design eliminates this challenge entirely.

حسب ضرورت اور OEM صلاحیتیں۔

We offer extensive customization options to adapt the LW-13/30 to specific site conditions, integration requirements, and end-user specifications:

• سکڈ ماونٹڈ ٹرنکی پیکجز: Pre-assembled compressor, motor, intercoolers, aftercooler, high-pressure discharge piping, instrumentation, and control panel on a structural steel skid. Factory pre-testing of all systems reduces commissioning time by 60%.
• خطرناک ایریا کنفیگریشنز: ATEX Zone 2 and IECEx compliant motor and electrical enclosures for petrochemical installations. Integrated gas detection and automatic ventilation interlocks.
• اعلی درجے کا عمل کنٹرول: Siemens S7-1200 or Allen-Bradley CompactLogix PLC with 10-inch HMI touchscreen, remote monitoring via Modbus TCP/IP or OPC-UA, and DCS/SCADA integration. High-pressure safety interlocks including automatic unload on overpressure and emergency isolation valves.
• ماحولیاتی تحفظ: C5-M marine-grade coatings for coastal installations; tropicalized electrical components for 55°C ambient; IP54-rated acoustic enclosures reducing noise from 85 dB(A) to 72 dB(A).
• OEM اور نجی لیبل: Custom paint colors, branded nameplates, and localized documentation for gas equipment distributors and system integrators.

اپنی مرضی کے مطابق ترتیب سے دستیاب ہیں MOQ 1 یونٹ. Engineering proposals are typically delivered within 5–7 business days. Standard delivery time is 12–14 weeks; repeat orders are delivered in 8–10 weeks.

Case Study: LNG Plant Nitrogen Purge & Inerting System

کلائنٹ: An LNG regasification terminal in Southeast Asia

چیلنج: The terminal required a reliable high-pressure nitrogen supply for pipeline purging, storage tank inerting, and emergency nitrogen injection into the LNG vaporization system. The existing oil-lubricated compressor was experiencing oil carryover into the nitrogen stream, contaminating the cryogenic heat exchangers and requiring quarterly cleaning shutdowns. The 2.50 MPa discharge pressure was also insufficient for the new high-pressure pipeline purge requirements. Maintenance costs had reached $95,000/year and unplanned shutdowns were occurring every 3–4 months.

حل: We supplied an LW-13/30 oil-free nitrogen compressor as the primary high-pressure supply, configured on a custom skid with integrated dual intercoolers, aftercooler, and a Siemens S7-1200 PLC control panel with SCADA integration. The 3.00 MPa discharge pressure met all pipeline purge and tank inerting requirements. The oil-free design eliminated heat exchanger contamination. A 3 m³ surge vessel was installed upstream to buffer demand fluctuations from the intermittent purge operations.

Quantified Results After 24 Months:

• نائٹروجن تیل کا مواد: Reduced from 2.8 mg/m³ to <0.01 mg/m³ISO 8573-1 کلاس 0 حاصل کرنا
• Cryogenic heat exchanger cleaning frequency: سہ ماہی سے سالانہ تک کم کر دیا گیا۔, saving $45,000/year
• Unplanned shutdowns: Zero events in 24 months versus 6 events in the previous 24 months
• سالانہ دیکھ بھال کی لاگت: 48% کی کمی ($95,000 to $49,400)
• Pipeline purge capability: Enhanced from 2.50 MPa to 3.00 MPa, meeting new regulatory requirements

“The LW-13/30 has been the most reliable piece of equipment in our nitrogen system. The elimination of oil contamination has solved our heat exchanger fouling problem, and the 3.00 MPa pressure gives us the purge capability we need for regulatory compliance. Our operations team finally has confidence in the nitrogen supply.” — Operations Manager, LNG Terminal

اکثر پوچھے گئے سوالات اور سلیکشن گائیڈ

متعلقہ مصنوعات اور حل

ہمارے ایک جامع جائزہ کے لیے صنعتی نائٹروجن کمپریسر پورٹ فولیو، بشمول آئل فری آکسیجن کمپریسرز، ہائیڈروجن کمپریسرز، کاربن ڈائی آکسائیڈ کمپریسرز، اور حسب ضرورت انجنیئرڈ خاص گیس سلوشنز، براہ کرم ہماری ایپلیکیشن انجینئرنگ ٹیم سے رابطہ کریں یا ہمارے آن لائن پروڈکٹ کیٹلاگ کو براؤز کریں۔

Ready to Upgrade Your Ultra High-Pressure Nitrogen System?

ہمارے ایپلیکیشن انجینئرز آپ کے نائٹروجن بہاؤ کی ضروریات، سکشن کی شرائط، خارج ہونے والے دباؤ کے اہداف، اور انضمام کی رکاوٹوں کا جائزہ لینے کے لیے کھڑے ہیں۔ ہم آپ کی انکوائری موصول ہونے کے 48 گھنٹوں کے اندر مفت تکنیکی تجاویز، فاؤنڈیشن لے آؤٹ ڈرائنگ، پائپنگ اور انسٹرومینٹیشن ڈایاگرام (P&IDs) اور ملکیت کی کل لاگت (TCO) کا تفصیلی تجزیہ فراہم کرتے ہیں۔

ای میل: [email protected] | 24 گھنٹے کے اندر جواب دیں۔